Junsi/iCharger iCharger DX12

With the new iCharger DX12, the renowned manufacturer Junsi has launched a DUO charger in a compact format.
The new DX12 charger combines the advantages of the well-known Junsi iCharger DUO series with the portability of a small pocket charger. Despite the small dimensions of 111.5 x 128.5 x 40 mm, no compromises have been made in terms of performance and ease of use. The newly developed rotary wheel has a very good pressure point and makes operation much easier.

Features

Charging current adjustable per output:0.05-30A
Charging current adjustable in synchronous mode:0.05-50A
Max. Number of NiCd/NiMH batteries:1-32
Input voltage:11-53V DC
Length (mm):111.5
Max. number of LiHv cells:12
Max. number of LiPo cells:12
Max. charging power at one output:1200W
Max. Output:1700W
Charging power Max Syncron:1800W
Balancer equalizing current per output:2A
Max. Discharge power:3000W
Discharge current adjustable for regenerative braking:30A
Max. Charging current:30A per channel, 50A in sync. mode
Max. Voltage lead batteries:40V
Balancer equalizing current synchronous mode:4A
Discharge power per output:50W
Input current limit:65A
Max. discharge power in synchronous mode:80W without external load
Micro SD card slot:Yes
Integrated power supply:No
Plug type charging output:XT60
Plug type input: XT90

Technical data

The technical data is impressive, 1700W charging power (from >25V), 1-12s LiXx cells and up to 30Ampere charging current are also sufficient for large batteries with high capacity. Of course, all other battery types such as LiHV, LiIo, NiZn, PB, NiCd or NiMh batteries can also be charged.
The discharge capacity is 80 watts in total (50 watts per output if only one output is used), but can be increased to up to 3000 watts using an external load (discharge resistor). Of course, the iCharger DX12 is also capable of regenerative charging. Here, the battery capacity is fed back into the supply battery from a full flight battery, for example.
The balancer current of 4 amps in total (2A per output) always ensures perfectly balanced cell voltages.
A USB-C PD port for charging smartphones etc. (5V/3A, 9V/2A, 12V/1.5A) or for software updates is also installed. The micro SD slot can be used to log data, but also for future updates.
Also integrated is a servo tester, please note that an external power supply is required!
The menu navigation is almost identical to the well-known Junsi iCharger 308DUO, 406 DUO or 4010DUO.
A 2.8" IPS LCD display ensures good readability even in low light.
Instructions in English are included with the charger in the form of a CD, the German version can be downloaded from our website.
All Junsi chargers of the X and DUO series are developed and approved for use in model making. Industrial use is not intended and therefore not permitted! All Junsi chargers may only be operated with power supply units developed for model making! AGM batteries must not be charged in the PB program!
ATTENTION: To be able to charge 12s, a 13-pin XH connector strip is required on the battery! There is NO balancer board included to be able to charge e.g. 2x6s as 12! (CB-12XH/EH)
For 10s as 2x 5s, the well-known CB-1010 can be used with the 11-11 wire!
* Charging a 12S battery with 2 balancer plugs *
You will need a circuit board with a connection cable that matches the battery and charger. Then observe the following sequence:
- First connect the charger to the mains adapter or a supply battery. If you are using a mains adapter, switch this on first.
Take care! Only connect to the charger when the batteries are correctly connected to the balancer board!
- First insert the first balancer plug of cells 1 - 6 "battery negative side, black cable" into the appropriate 6S slot on the circuit board from the negative side,
- then plug the second balancer plug of cells 6-12 into the second 6S slot from the positive side "batteries positive side, red cable". Now connect it to the charger. If it has not flashed and smoked up to this point, you have done everything right!
- Now connect the thick red main charging cable "+" of the battery to the charger, followed by the thick black main charging cable "-".
Connections: Avoid short circuits, otherwise there is a risk of injury! This sequence also applies when charging several batteries in series!
You are responsible for any damage or defects that may occur if this is not observed!


• Latest synchronous buck-boost technology for maximum power with small dimensions
• DUO charger with 2 equivalent charging outputs with max. 1200W each / total 1700W
• USB-C port with PD (Power Delivery) for charging current smartphones etc. 5V/3A, 9V/2A, 12V/1.5A
• Micro SD slot for data log // Integrated servo tester // Channel 1 can be used as a power supply unit 2V-50V, 1A-30A
• Total 4A balancer current (2A per output) Very compact and lightweight (LxWxH 111.5 x 128.5 x 40 Weight 500g

Scope of delivery

1x Junsi/iCharger iCharger DX12