- Novelties
- Back in stock
- Sell-Out
- Special Deals
Building Blocks- RC Helicopter
- RC Multicopter
- RC Planes
- RC Cars
- RC Boats
- RC Motorcycles
- RC Functional Models
- RC Simulators
- BEASTX
- Engine Electric
- Engine Nitro
- Batteries
- Electronics
- FPV / Cameras
- Measuring Tools
- Tools
- Accessories
- Outdoor
- Merchandising
- Reference books
- Gift Voucher
- Identification-Plates
- Sonderposten
AGF-RC A19DLM SERVO
Picture can be different from original item
The AGF-RC A19 DLM is a 12mm mini servo with an all-aluminum housing. The servo is HV capable and can be operated directly from a 2s LiPo (4.8 - 8.4V).
With an actuating force of 4kg, this small power proftz can be installed anywhere where space is limited but high actuating forces and a backlash-free gearbox are required.
With dimensions of 22.9*12.8*22 mm, it is ideal as an upgrade servo in 1/10 Rc cars such as Traxx.B for upgrading your Traxxas 1/10 models, 1/10 RC Crawler TRX-4 TRX-6, Axial SCX10 III, Capra or 1/18 TRX4M, Aixal 1/10 SCX10 III Jeep JL Warngler 4WD, Absima 1:10 EP Crawler, Absima Sherpa CR3.4 1/10 Crawler, Absima 1:8 EP Crawler, Vanquish Phoenix, Absima Sherpa etc..
The A19DLM is also programmable with the optional USB Inteface AGF-SP.
This requires a Windows computer with Windows 7 or 10. The servos are supplied directly via the USB port and only need to be plugged into the interface. In the software, for example, the soft start, the neutral point, the servo travels can be adjusted (larger and smaller) or the direction of rotation can be set. Furthermore, the Sanwa SSR mode can be activated if required, which is of particular interest to RC car drivers. The integrated overload cut-off can also be adjusted in 3 stages and you can select what should happen in the event of signal loss.
Of course, these are optional features, all servos can be operated as normal straight out of the box and do not need to be adjusted beforehand!
Actuating time S2/60° (sec): 0.088
Actuating time S1/60° (sec): 0.095
Width (mm): 12.8
Weight (g): 19
Height (mm): 22
Length (mm): 22.9
Actuating force S1 (kg*cm): 3.5
Actuating force S2 (kg*cm): 4
Voltage range: 4.8V-8.4V
Control frequency: Up to 333Hz, center pulse 1520us
High-voltage capable up to 8.4V: Yes
Motor type: Brush motor
Recommended applications: Helicopter, airplane, car, boat
Ball bearings (number): 2
Output teeth (number): 25
Voltage 1 (Volt): 7.4
Housing type: Full metal
Voltage 2 (Volt): 8.4
Classification: Mini
Gear type: Titanium
With an actuating force of 4kg, this small power proftz can be installed anywhere where space is limited but high actuating forces and a backlash-free gearbox are required.
With dimensions of 22.9*12.8*22 mm, it is ideal as an upgrade servo in 1/10 Rc cars such as Traxx.B for upgrading your Traxxas 1/10 models, 1/10 RC Crawler TRX-4 TRX-6, Axial SCX10 III, Capra or 1/18 TRX4M, Aixal 1/10 SCX10 III Jeep JL Warngler 4WD, Absima 1:10 EP Crawler, Absima Sherpa CR3.4 1/10 Crawler, Absima 1:8 EP Crawler, Vanquish Phoenix, Absima Sherpa etc..
The A19DLM is also programmable with the optional USB Inteface AGF-SP.
This requires a Windows computer with Windows 7 or 10. The servos are supplied directly via the USB port and only need to be plugged into the interface. In the software, for example, the soft start, the neutral point, the servo travels can be adjusted (larger and smaller) or the direction of rotation can be set. Furthermore, the Sanwa SSR mode can be activated if required, which is of particular interest to RC car drivers. The integrated overload cut-off can also be adjusted in 3 stages and you can select what should happen in the event of signal loss.
Of course, these are optional features, all servos can be operated as normal straight out of the box and do not need to be adjusted beforehand!
Technical data:
Actuating time S2/60° (sec): 0.088
Actuating time S1/60° (sec): 0.095
Width (mm): 12.8
Weight (g): 19
Height (mm): 22
Length (mm): 22.9
Actuating force S1 (kg*cm): 3.5
Actuating force S2 (kg*cm): 4
Voltage range: 4.8V-8.4V
Control frequency: Up to 333Hz, center pulse 1520us
High-voltage capable up to 8.4V: Yes
Motor type: Brush motor
Recommended applications: Helicopter, airplane, car, boat
Ball bearings (number): 2
Output teeth (number): 25
Voltage 1 (Volt): 7.4
Housing type: Full metal
Voltage 2 (Volt): 8.4
Classification: Mini
Gear type: Titanium
Restocking
| Item number | AGF-A19DLM |
| Manufacturer | AGF-RC |
| Packing weight | 0,0 Kg |
Tell a friend